Metal Deck In Stock. Same Day Shipping.

N Deck (N-24)
Good in Stock. Same Day Delivery or Pick Up.

  • Verco Roof Deck Catalog

    Download the Verco Roof Deck Catalog Below

  • ICC Report

    Download the ICC Report Below

    ICC report
  • Los Angeles Research Report

    Download the Los Angeles Research Report Below

    Los Angeles Research Report
  • IAPMO Report

    Download the IAPMO Report Below

    IAPMO Report
  • Attachment of Roof Deck

    Support Fastening

    The diaphragm shear tables of this catalog include two methods of attaching deck to the supports: welds and mechanical fasteners (power actuated fasteners or self-drilling, self-tapping screws).

    Figure-3 B-Deck Arc WeldWelds: When Vero roof deck is to be welded to supports, the effective fusion area is to be at least ½ in. diameter for arc spot (puddle) welds (Figure 3) or at least 3-i in. x 1 in. long for arc seam welds. Arc seam and arc spot welds are to be located and spaced as described in the tables.

    Hilti Fasteners: Hilti X-EDNK22 THQ12, X-HSN 24, or X-ENP-19 L15 fasteners are to be installed as shown in Figure 4. Hilti X-HSN 24 fasteners have a dome style head, red guidance washer and a steel silver-colored top-hat washer. Hilti X-EDNK22 fasteners have a dome style head, a 15-ew inch diameter steel flat washer, and a steel top hat washer. The Hilti X-ENP-19 fastener has a fully knurled tip and tapered shank fitted with two 0.590-inch diameter steel cupped washers. Contact Hilti for additional information on the fasteners.

    Proper penetration of the Hilti fasteners into structural supports is shown in Figure 4. Fasteners shall be located not less than 1 in. from the end of the sheets.

    Select the appropriate fastener based on the actual substrate thickness.

    Figure-4

    Pneutek Fasteners: Pneutek K66062, K66075, K64062, K64075, SDK63075, or SDK61075 fasteners are to be installed as shown in Figure 5. The Pneutek fasteners have ½ inch diameter heads. Contact Pneutek for additional information on the fasteners. Fasteners must be driven with the Pneutek Air/Safe fastening system to ensure tight contact between the fastener head and the attached deck as shown in Figure 5. Fasteners shall be located not less than 1 in. from the end of the sheets.

    Select the appropriate fastener based on the actual substrate thickness. Note that K66075 or K64075 pins are to be used for attachment of four layers of 20 gage deck or three or four layers of 18 or 16 gage deck.

    Figure-5

    Figure-6Screws: #12 self-drilling, self-tapping screws are to be installed as shown in Figure 6. Diaphragm shear and flexibility values are based on SDI recognized #12 screws from Buildex, Elco, Hilti, and Simpson Strong-Tie when installed in supports at least 0.0385 inches thick. The tabulated shears and flexibility values may be modified in accordance with appropriate footnotes of the Diaphragm Shear Strength and Flexibility Tables for supports of different thicknesses or for screws (“generic”) which are not recognized by SDI.
  • Sidelap Attachments

    Sidelap Connections

    Verco roof decks are to be fastened at the sidelaps by one of four methods: VSC2s made with the PunchLok II Tool, 1½ in. long top seam welds, button punches, or #10 x ¾ in. long screws. Spacing of sidelap connections shall be as specified in the tables.

    Figure-7

    The dimension from the centerline of the supports to the first and last sidelap connection within each span is to be no more than one half the specified spacing as shown in Figure 7. The number of connections per span based on spacing are listed in Table 3.

    Table-3


    Figure-8PunchLok® II System: The connection made by the PunchLok II Tool is referred to as a VSC2 (Verco Sidelap Connection 2). An acceptable VSC2 connection has been made when the sidelap material has been sheared and offset so the sheared surface of the male leg is visible in the cut (Figure 8).

    The VSC2 connection may be made in either direction relative to the sidelap.

    Top Seam Welds: When roof deck sidelaps are connected with top seam welds (TSW) (Figure 9, left), the 1½ in. long weld must engage the top of the inner (male) leg. Clinch the joint before welding to create contact between the lips.

    Figure-9

    Button Punches: When roof deck sidelaps are connected with button punches (Figure 9, right), an average-sized person should be able to stand (not jump) on the flute adjacent to the attachment without the joint coming apart.

    Figure-10Screws: When self-drilling, self-tapping screws are used to connect the sidelaps of roof decks, they are installed as shown in Figure 10. The diaphragm shear values and flexibility factors shown in the tables of this catalog are based on minimum #10 self-drilling, self-tapping screws. The “SS” designation for roof deck indicates interlocking deck provided with extended female lip for screw fastening. The “NS” designation for HSN3 roof deck indicates deck provided with nested sidelap. Deep and Shallow VERCOR deck are provided with a nested sidelap.

    Parallel Collectors

    Spacing of the attachments at diaphragm chords, struts, ties or other collector elements that are parallel to the deck flutes is based on the actual shear to be transferred and shear capacity of the connections used. The spacing of the connections at these shear transfer elements parallel to the deck flutes should not be larger than that for the interior sidelap connections in order to maintain diaphragm rigidity. The maximum spacing of attachments at parallel collectors is 3 ft. Allowable shear loads for Arc Spot Welds, Arc Seam Welds, Hilti Fasteners, Pneutek Fasteners, and SDI Recognized Screws are listed in Table 4. Allowable shear loads for #12 screws that do not meet the requirements of SDI Recognized Screws are listed in Table 5.

    Fillet Welds: Spacing of fillet welds used at collectors parallel to the deck flutes should be based on the shear to be transferred. Allowable shear strength for fillet welds should be determined in accordance with AISI S100.
  • Roof Deck Finishes

    Roof Deck Finishes

    • Galvanized G-60 or G-90. Galvanized roof deck panels are formed from either ASTM A 653 or A 1063 steel.

    • Cold Rolled with Gray Primer. Acrylic primer is applied to cold rolled steel either ASTM A 1008 or A 1039.

    • Galvanized with Gray or White Primer. Custom Order Only.

    • B Deck is a structural product. Minor dents and scratches which do not affect the structural capacity of HSB-36 are not grounds for rejection.
  • Shear Tranz II

    Shear Tranz II

    • Verco introduced the use of restraining elements such as the ShearTranz II-42 system, to increase roof deck diaphragm rigidity

    • The 14 Gauge Shear Tranz II-42 elements are used with PLB-36 deck with sidelaps connected using the Punchlok II tool.

    • The ShearTranz II-42 elements are used at shear collecting support elements perpendicular to the metal deck corrugations. When ShearTranz II-42 elements are used, the deck does not need to terminate at the support as it may be cantilevered.

    • Metal deck end laps of PLB-36 with ShearTranz II-42 system must be at least 2 inches and fastened to supports with arc spot and arc seam welds. ShearTranz II elements are required if butted end joints are used. See installation details shown on page 66 of VR4
  • Profile Closures

    Profile Closures

  • Vent Tabs

    Vent Tabs

    • Verco roof deck is available with factory punched vent tabs to provide positive venting (see Figure 11). Determine venting requirements based on the specific materials installed over the deck. Some leakage during lightweight insulating concrete placement should be anticipated with vented deck. Vent tabs projecting upwards are staggered in interior low flutes at approximately 6 in. on center.
      • HSB-36 and PLB-36 = 5 Rows of Vent Tabs
      • N-24 and PLN-24 = 2 Rows of Vent Tabs
      • N3 and PLN3 = 3 Rows of Vent Tabs
    Click here to download the pdf file.

    vent tabs
  • Fire Ratings

    Fire Ratings

    Hourly fire ratings, if required, may affect the maximum allowable deck span and/or minimum deck gage. Refer to the UL Fire Resistance Directory or Verco’s Evaluation Report for further information. Note that only Verco cold rolled with Verco factory gray primer and Verco galvanized finishes are approved for use with spray applied fire proofing.
  • Autocad

    AUTOCAD Details for Download

N-Deck Section Properties

3" Deep N-24 Long Span Roof Deck
Good in Stock. Same Day Delivery or Pick Up.

N Deck is strong, light weight, economical, and easy to install. This panel is used in long span conditions ranging from six feet to sixteen feet in distance. N-24 Deck is 3" deep and is available in galvanized and prime painted finishes. N Deck is good in stock in the following gauges 20, 18, 16 Gauge. In addition, N-24 Deck is available in lengths ranging from 20'-6" to 35'-6". Material can be custom run to longer or shorter lengths if needed.
    • 3" Deep Roof Deck
    • ICBO 2078-P
N roof deck is used in a variety of applications such as Roofs, Canopies, Awnings, Roof Screens, etc.

N-24 is in stock in Ontario, California or Phoenix, Arizona. In addition, orders can be manufactured at the metal deck plant in Northern California or any of the other metal deck facilities throughout the country. Route trucks run throughout the country on a weekly or monthly basis depending on your location and can be shipped very inexpensively. Please click below for a Quote or Call 877-787-5467.

You May Also Be Interested In These Products:

Metal Purlins
Metal Purlins and Cee Channel are in stock. Cee Purlins and Zee Purlins. Galvanized and Red Prime Painted.
Metal Roofing Panels
7/8" Corrugated, R Panel, Standing Seam, Western Rib, and Flush Wall/Soffit Panels. Painted and Galvalume®. Fast Turnaround and Excellent Customer Service.
Real Rusted Roofing
Rusted Roofing is produced in two different finishes: A606-4 (aka Corten) or Bare steel. Available panels include corrugated, standing seam, R-Panel, flush wall & more.
Painted Rusted Roofing
We are the leading provider of painted metal roofing panels designed to look like real rusted roofing without the rust stains. Learn more.
Painted Products That Look Weathered Galvanized
Painted metal roofing and siding that looks like an old dull gray and weathered galvanized roof. Many styles and finishes to choose from.
Painted Products That Look Like Patina'd Copper
Why pay for an expensive copper roof? Metal roofing and siding that has been pre-painted to look like patina'd copper is a growing favorite among architects and builders.
Vari-Cool®
VARI-Cool Color Changing Paint System. This Exotic Paint System Is Unlike Anything You Have Ever Seen. 17 Different Colors - Request A Color Chip.
Metal Carports
Heavy duty inexpensive DIY metal carports and RV shelters. Large selection of shelters and carports for all of your storage needs. Route trucks servicing the entire country.
Metal Deck
Roof deck and floor deck in stock. Huge selection of gauges, lengths, and metal decking profiles. Immediate availability. Buy Now.
Galvanized Square Tubes
Galvanized square tube in stock in 14 gauge at many different lengths. Galvanized tube used for metal fence posts, metal carports, deck posts, panic bar gates, or building supports.
N Deck (N-24) N Deck (N-24)
Button Punch Tool
Button Punch Tool
Button punch tool available for button punching or crimping seams of metal deck for easier welding. Purchase today.
Shop now
Parker Punch Tool
Parker Punch Tool
The Parker Punch Tool is a fast, high-volume pneumatic button punch that can save you time while providing strong, high quality punches.
Shop now
Edge Form/Pour Stop
Edge Form/Pour Stop
These formed galvanized angles are used to create a stopping point for poured concrete. Edge form and pour stop immediate availability and delivery. 16 Gauge, galvanized in stock. Custom sizes and...
Shop now
Cell Closures
Cell Closures
Cell closure will close off the open ends of metal floor deck. This will prevent concrete spilling through ends of the metal deck. Available in 20 Gauge, Galvanized at 1.5" X 1.5", 1" X 2", 1" X 3"
Shop now
N Deck, Inside, 3" Foam Individual Plugs
N Deck, Inside, 3" Foam Individual Plugs
N Deck, Inside, 3" Foam Individual Plugs (Grey, Box of 100)
Shop now
N Deck, Outside, 2' Foam Closure Strips
N Deck, Outside, 2' Foam Closure Strips
N Deck, Outside, 2' Foam Closure Strips (Grey, Box of 100)
Shop now
Metal Closures
Metal Closures
Galvanized metal profile closures for metal deck. Metal Closures available for most metal deck profiles. Immediate availability and delivery.
Shop now
Shop Drawings
Shop Drawings
We are ready to provide shop drawings services and metal deck packages for your next project.
Shop now
PLN-24™ Roof Deck
PLN-24™ Roof Deck
Punchlok® II N Deck (PLN-24) including use of the Punchlok®-II tool. Large selection of sheet lengths and gauges. Good in stock. Same day delivery or pick up.
Shop now
Metal Deck Fasteners
Metal Deck Fasteners
Shop metal deck screws, fasteners, and impax self-drilling fasteners for metal decking installation and applications.
Shop now
Call Us!
Request A Quote
Request A Color Chip